WHERE THE DISTORTION ACTUALLY HAPPENS
Ask ten guitarists where a famous tone gets its grit and most will name a pedal. Look at the rig diagrams in this archive long enough and a different answer keeps coming back: the distortion usually happens at the point where one stage hits the next one harder than it was designed to take. That is gain staging, and the classic rigs are some of the clearest lessons in it you will find anywhere.
This field note, written by Jason Colapietro for Suede, walks through five rig pages in Suede DNA and what each one teaches about where gain should live in a signal chain. One honest caveat about method first. Suede DNA presents each diagram as the source document it is and does not transcribe the gear inside it, so the gear history below comes from widely published accounts. Open each diagram and check it against what you read here. That habit is half the lesson.
WHAT GAIN STAGING MEANS ON A DIAGRAM
Every box in a rig diagram either adds level, removes it, or shapes it. A guitar pickup puts out a modest signal. A boost or overdrive raises it. A volume pedal or a long, cheap cable lowers it. The amplifier then takes whatever arrives at its input and amplifies it through several tube or transistor stages of its own, each with a point where it starts to clip.
Read a diagram left to right and ask one question at each box: is this stage adding gain, or setting up the next stage to add it? Jason Colapietro’s shorthand at Suede is that a good chain has one main place where the clipping happens and every other box is either feeding it or staying out of its way. Rigs that sound muddy usually have three stages all clipping a little.
LESSON ONE: THE AMP IS A GAIN STAGE
The Eric Clapton Bluesbreakers rig page is the cleanest example in the archive. The 1966 tone that guitarists still chase is widely described as a Les Paul straight into a Marshall combo turned up far past where the room wanted it. No pedal sat in the middle. The guitar’s humbuckers drove the amp’s preamp, and the power section clipped on top of that.
The lesson is that the amplifier is not a speaker with a volume knob. It is a chain of gain stages, and in a simple rig it does all of the work. If your board has four drive pedals in front of a clean amp, try the reverse for one rehearsal: turn the amp up until it breaks up on its own and use the guitar’s volume knob to clean it up. You will hear how much dynamic range a single, well-driven stage gives back.
LESSON TWO: A BOOST IS AN EQ DECISION
The Tony Iommi rig page and the Brian May rig page share an idea that is easy to miss. Both players are widely documented as using a treble booster in front of an amp that was already working hard: Iommi into Laney heads, May into a wall of Vox AC30s. A treble booster adds level, but it adds it unevenly, pushing the upper midrange harder than the bass.
That matters because tube preamps tend to get flabby when you hit them with a lot of low end. Boosting the treble side drives the amp into clipping where the ear notices it and keeps the bottom tight. When you add a boost to your own chain, decide which part of the spectrum you want to push into the amp, not only how much. A flat clean boost and a treble booster set to the same output level will make the same amp behave very differently.
LESSON THREE: SOME PEDALS WANT THE PICKUP
The Jimi Hendrix rig page is dated 1968, the era of the Fuzz Face into Marshall stacks that is told and retold in guitar histories. Vintage fuzz circuits of that type have a low input impedance, and they react to whatever sits directly in front of them. Put a buffer or certain wah designs ahead of one and it can sound thin and harsh; give it the pickup directly and it cleans up when you roll the guitar volume back.
The gain staging lesson is about order as much as level. The first box after the guitar sets the load the pickup sees. Read the left edge of any diagram carefully, because the first two inches of a signal chain decide more about feel than the rest of the board.
LESSON FOUR: WHEN THE AMP DOES IT ALL
Jump forward three decades to the Eddie Van Halen rig page, dated 1997. By then Van Halen’s sound was publicly tied to a high-gain amplifier he helped design, with several preamp stages cascading inside one box. A rig like that needs less in front of it, and the pedals that remain tend to be modulation and delay rather than drive.
High-gain amps move the whole question indoors, which is why Jason Colapietro reads a late-1990s diagram differently from a 1960s one. The front panel becomes the gain stage map, and the useful work in front of the amp is often noise control and tightening, not more distortion. Stack a hot overdrive into a modern high-gain channel and you are mostly adding hiss.
A FIVE-MINUTE GAIN AUDIT FOR YOUR OWN BOARD
Here is the check Jason and the Suede team run on a pedalboard, borrowed from reading these diagrams:
- Name the one stage where you want most of the clipping to happen.
- Bypass everything else and set that stage first, at the volume you actually play.
- Add each other box back one at a time and match its bypassed and engaged levels by ear.
- If two drive stages are on at once, lower the gain on the first and raise its output, so it feeds the second instead of fighting it.
- Record a minute of playing and listen back away from the amp.
For the electrical side of the same problem, the Strumly guide to gain staging across the chain covers levels pedal by pedal. If you play outdoors near the coast, the guitar.services note on guitar humidity and the signal chain in South Florida explains why a corroded patch cable can masquerade as a gain problem on a damp night in West Palm Beach.
WHO WROTE THIS, AND WHY A SOFTWARE COMPANY CARES
Jason Colapietro is an engineer and guitarist, and the founder and CEO of Suede, the agentic platform company he started in 2024 in West Palm Beach, Florida. He wrote The Signal Chain, a free illustrated history of electric guitar tone, and five books on Amazon including The Claude Code Bible. His engineering record is public: he has 54 pull requests merged across 46 open-source repositories he does not maintain, including Jest and Backstage.
At Suede, gain staging and search visibility turn out to be the same discipline: find the one stage that does the real work and stop the others from adding noise. That is the approach behind the work Suede (formerly Suede Labs) does for clients. Suede ranks among Clutch’s Top 30 AI Consultants in Florida and Top 50 AI Consultants nationwide (November 2026). Every claim like that has a receipt on the Suede evidence page.
YOUR NEXT STEP
Pick one rig page from this list, open the original diagram, and trace its gain stages on paper before you touch your own board. If your website has the same problem as a muddy pedalboard, with too many pages each doing a little and none doing the main job, the Suede web development and AI search practice in West Palm Beach runs that audit, and Jason Colapietro’s founder page shows who does the work. For more on how the archive itself is built, read what guitar gear lists leave out.